Guide

How to measure a window well for a cover (Knoxville, TN)

Simple measuring guide for Knoxville TN window well covers — length, width, depth. Free Estimate from our team.

  1. Measure the longest inside length and widest inside width at the top of the well
  2. Note depth from the top rim to the window sill or well floor
  3. Sketch whether the shape is round, rectangular, or irregular
  4. Photo the well from above with a tape visible if you can
  5. Note if the window is an egress / escape opening

Bring those notes to your Free Estimate request — we’ll confirm fit before anything is finalized. East Tennessee wells vary; measuring beats guessing.

Tools

  • A tape measure, at least 16 feet.
  • A notepad or phone for notes.
  • A phone camera.
  • A helper, if possible.
  • Gloves; wells can hide sharp edges, wasps, and snakes.

Step by step

1. Identify the well shape

Most wells are one of these:

  • Semicircle (corrugated steel or composite). The most common on newer homes.
  • Rectangle or square. Often concrete, block, or stone.
  • Rectangle with rounded corners.
  • Irregular. Stone or block wells on older homes, bowed walls, or wells that span two windows.

2. Measure the width

Measure the inside width at the top rim, from the outside edge of the rim on one side to the other, parallel to the house. For a cover that sits on the rim, the outside dimension matters. Note both inside and outside measurements if the rim has a flange.

3. Measure the projection

Measure from the foundation wall straight out to the farthest point of the rim. This is often called the projection or depth from the wall.

4. Measure the depth

Measure from the top of the rim down to the bottom of the well (the gravel). Then measure from the rim down to the window sill. These matter for egress and drainage.

5. Note the height above grade

How far does the rim stick up above the soil? Covers that sit on the rim need some rim exposed.

6. Measure the wall

How far is the rim from siding, brick, or stone above the foundation? This tells us whether a cover needs a back flange or riser.

7. Note anything in the way

Pipes, vents, conduit, downspouts, hose bibs, AC lines, shrubs, decks, or stairs near the well.

8. Photograph it

Take photos from above, from the side, and straight on, with the tape measure visible in at least one.

Measuring irregular wells

For a well that is not a clean shape, take several width measurements at equal distances out from the wall, and several projection measurements along the width. A rough sketch with these numbers helps. Very irregular wells may need an on-site template.

Common mistakes

  • Measuring the inside of the well only, when the cover sits on the outside of the rim.
  • Measuring from siding instead of from the foundation.
  • Forgetting the window is egress.
  • Rounding too much. Measure to the nearest quarter inch.
  • Measuring only one of two similar-looking wells. Wells on the same house often differ.

Egress windows

If the window is in a bedroom or is a required escape opening, note that. The cover must open from inside without tools. See our egress window well basics.

What we do with your measurements

Your numbers help us give a rough idea of options and price before we visit. We confirm measurements ourselves before anything is ordered or fabricated, so you are not on the hook for a mistake. See custom-fit covers and costs.

Where we work

Free Estimates in Farragut, Karns, Oak Ridge, Alcoa, and nearby. See our services.

A worked example

A homeowner in Karns has three corrugated steel wells. She measures each:

WellWidth at rimProjectionDepth to gravelNotes
Back left40 in18 in36 inUnder gutter
Back right40 in18 in36 inNext to patio
Bedroom44 in38 in48 inEgress, ladder in well

The two back wells look the same, but she measures them anyway and they match. The bedroom well is deeper and wider and has a ladder, so it needs a hinged egress cover. With her numbers and photos, we can suggest options before a visit and confirm on site.

Measuring for a back flange

If a cover needs to meet siding or brick above the foundation, measure from the top of the well rim straight up the wall to the bottom of the siding or brick ledge. Measure at both ends, since the rim may not be level. Note what the wall is made of.

Measuring for egress

For an egress well, also note whether there is a ladder or steps, where they are, and how much clear space there is between the ladder and the window. The cover's hinge and struts must not block that space.

Sending measurements

When you request a Free Estimate, include the measurements, the photos, which windows are egress, and anything special: a radon pipe, a downspout, HOA rules, or a well that has pulled away from the house.

Double-check before you send

Re-measure any number that looks odd, and label each well in your photos so it is clear which numbers go with which well.

More measuring questions

How do I measure a window well for a cover?

Measure the width at the top rim parallel to the house, the projection from the foundation wall to the farthest point, the depth, and the height of the rim above grade. Photograph with a tape visible.

Should I measure the inside or outside of the rim?

For covers that sit on the rim, the outside dimension usually matters. Note both if the rim has a flange.

What if my window well is irregular?

Take several width and projection measurements and sketch the shape. Very irregular wells may need an on-site template.

Do I need to measure the distance to the siding?

Yes. It tells us whether a cover needs a back flange or riser to meet the wall.

Will you rely on my measurements?

They help with a rough estimate. We confirm measurements ourselves before anything is ordered or fabricated.

How do I measure for a back flange?

Measure from the top of the rim straight up to the bottom of the siding or brick ledge, at both ends, and note the wall material.

What extra should I note for an egress well?

Whether there is a ladder or steps, where they are, and the clear space between the ladder and the window.

How precise should my measurements be?

To the nearest quarter inch, with each well labeled in your photos.

Get covers measured and installed

When you are ready, see our window well cover installation in Knoxville page for cover types, egress rules, how we measure, and how to request a Free Estimate.

Related guides

When you’re ready

Request a quote

Tell us your city or ZIP, how many wells, and whether any are egress openings. We’ll follow up with a Free Estimate.

Request a quote

Or call (865) 381-0951

Knoxville Window Well Covers Call (865) 381-0951