What we offer

Window Well Cover Installation in Knoxville, TN

Custom-fit polycarbonate, steel and combination covers for basement window wells, measured on site and installed so egress windows still open from inside. Request a Free Estimate when you are ready.

Custom & standard covers

Measure the opening, match the footprint — including odd East Tennessee wells.

Metal & polycarbonate

Strength vs daylight tradeoffs for Smokies-edge weather and leaf load.

Egress-minded options

Covers that can open from inside when the window is an escape opening.

Debris & yard safety

Leaf shedding and fall protection for kids and pets — honest limits.

Window well covers we install

Every house is different, but most Knoxville window wells fall into a few types: galvanized steel liners shaped like a half circle or rectangle, tiered or stepped wells for larger egress windows, and older wells made of block, brick or stone. We fit covers to all of them.

Clear polycarbonate covers

Polycarbonate is a tough, clear plastic, many times stronger than glass or acrylic. A polycarbonate cover keeps out rain, leaves, snow and animals while letting daylight reach the basement. Flat covers sit low and look clean. Domed covers shed water and leaves well and give more headroom in the well. We use UV-stabilized material that resists yellowing in the sun. Read more in polycarbonate clarity and UV.

Steel grate covers

Steel grates are welded bars, usually powder-coated or galvanized, that can carry a person’s weight. They are the strongest option and are a good fit for wells next to patios, walkways or play areas. They let light and air through but not much protection from rain.

Combination covers

A combination cover puts a polycarbonate top over a steel frame or grate. It is strong enough to stand on and still keeps weather out. For families with small children or large dogs, this is the most common choice.

Custom covers

Odd shapes, extra-large egress wells, stone wells and wells with uneven tops need custom covers. We measure carefully, including the outer edge, the shape of the curve, and how the well meets the foundation, then have the cover made to fit. See custom-fit window well covers.

Egress-safe hardware

If the window is an escape opening from a basement bedroom, the cover must open from inside without a key, tool or special knowledge, and without more force than the window itself needs. That is the rule in the International Residential Code that Tennessee codes follow. In practice that means:

  • No screws, padlocks or bolts that only open from outside.
  • Hinged covers that swing up and out of the way, or lift-off covers light enough to push up.
  • Gas struts on larger covers so they are easy to push open and stay open.
  • A clear path: the well itself must meet size rules, and wells deeper than 44 inches need a permanent ladder or steps.

We test every egress cover from inside the well before we leave. If the well itself does not meet egress size rules, we will tell you. That matters if you are finishing a basement or selling a home with a basement bedroom. Read egress window well basics for details.

How we measure and install

A cover that does not fit lets leaves and water in around the edges, rattles in the wind, and can blow off in a storm. Good measuring is most of the job.

  1. Width and projection. We measure across the widest point of the well and from the foundation wall out to the farthest edge.
  2. Shape. Half-round, rectangular, tiered or custom. For curved wells we note the curve so the cover follows it.
  3. The top edge. Steel wells have a rolled lip; block and stone wells have flat or uneven tops. This decides how the cover attaches.
  4. Siding and trim. Many covers attach to the foundation or siding. We look at what is there so the cover sits tight without damaging the house.
  5. Egress check. We note which wells serve escape windows and plan hardware for them.

On install day we clean the well, check the drain, set the cover, attach it, and check the fit and operation. Most installs take an hour or two. See our install timeline for what to expect from first call to finished covers.

What affects the price

  • Size. Larger egress wells need bigger, heavier covers.
  • Shape. Standard rectangles and half circles cost less than tiered, round or custom shapes.
  • Material. Polycarbonate, steel grate or combination, and the load rating.
  • Hardware. Hinges, gas struts and egress releases add cost.
  • Number of wells. Doing several wells at once is more efficient than one at a time.

We quote each well separately so you can choose where to spend. See the Knoxville window well cover cost guide.

Care after install

Covers need little care. Brush leaves off the top in fall, rinse polycarbonate with water and mild soap (not glass cleaner with ammonia, which can cloud it), and check that hinges and latches move freely once a year. If a cover is on an egress well, open it from inside once in a while so everyone in the home knows how.

Who calls us

Most calls come from a few situations. A family moves into a home with open wells and a toddler. A basement takes on water after a summer storm. A homeowner is finishing the basement and wants more light without leaves on the windows. An HOA asks for covers that look tidy. A home inspector flags an egress well with a cover that does not open from inside. Each case starts the same way: measure the wells, choose the right cover, and fit it properly. Our HOA guide and pets and kids safety guide cover two of the most common reasons.

We serve Knoxville and the surrounding towns in Knox, Blount, Loudon, Anderson and Sevier counties. See the service area for town pages.

Why East Tennessee window wells need extra attention

Most of the Knoxville area is ridge-and-valley country: long, parallel ridges with valleys between them. Houses are often built into slopes, so a basement may be fully underground on one side and open on the other. Window wells along the buried side are the low point for anything that falls or flows toward the house.

  • Leaves and needles. Knox, Blount and Anderson counties are heavily wooded. A single big oak can drop enough leaves to fill a well in one fall.
  • Heavy storms. Summer thunderstorms can drop a lot of rain in a short time. An uncovered well catches all of it.
  • Clay and limestone soils. Much of the region has clay soils over limestone. Clay drains slowly, so water that collects at the bottom of a well can take a long time to soak away.
  • Wildlife. Frogs, toads, snakes, chipmunks and even small birds fall into open wells and can’t get out.

A good cover deals with the first and last problems completely, and helps a lot with the second. It does not change how the soil drains, so if a well stays wet after a dry week, the drain at the bottom or the grade around the well needs a look as well.

Signs your wells need covers

  • You clean leaves out of the wells more than once a season.
  • Water stands in a well after rain.
  • You find animals trapped in the wells.
  • The basement windows are always dirty or streaked.
  • Children or pets play near the wells.
  • You have an egress well with no cover, or a cover that does not open from inside.

Covers and basement moisture

Window wells are one of the most common places water gets into a basement. Water rising in a well finds the gaps around the window frame and runs down the inside wall. Homeowners often blame the foundation when the real cause is a well full of leaves and rain. A cover keeps rain out of the well, keeps leaves off the drain, and keeps the window frame drier. If your basement gets damp after storms and the wells are open, covers are one of the cheapest things to try first. Our window wells and basement flooding guide explains how to tell the difference between well water and other sources of basement moisture.

Ventilation

Some homeowners worry that a cover will trap moisture in the well. Most covers leave a small gap or have vents so air can move. If you open basement windows for fresh air, choose a cover that can be propped open or has built-in vents.

What to send for a Free Estimate

  • Your town or ZIP.
  • How many wells you have, and which ones serve bedrooms.
  • The shape of each well: half-round, rectangular, tiered, or something else.
  • What the wells are made of: steel, block, stone or poured concrete.
  • A photo of each well from above, with something for scale if you can.
  • Any problems: water, leaves, animals, a cover that does not fit, or a cover that does not open.

We use that to give you a rough idea of options before we come out to measure. Final measurements happen on site.

Covers for basements being finished

Finishing a basement is the most common time to think about window wells. New drywall, carpet and furniture make a wet window well much more costly. If a room will be used as a bedroom, the window and well must meet egress size rules and the cover must open from inside. Plan covers with your contractor before the walls go up, so the window, the well, any ladder and the cover all work together. We can measure during the project and install covers once outside grading is finished. Our egress basics guide lists the key measurements.

Window well cover service questions

Do you install covers on round or tiered wells?

Yes. Round, scalloped, tiered and stone wells are common around Knoxville. We measure each one and fit the cover to the actual shape.

Can you make a cover lockable?

On non-egress wells we can add hardware that keeps the cover secure from outside. On egress wells, the cover must open from inside without a key or tool, so we use hardware that secures it from outside but releases easily from inside.

Will polycarbonate turn yellow?

Quality polycarbonate made for outdoor use is UV-stabilized to resist yellowing and getting brittle. Cheap acrylic covers yellow and crack much faster. We list the material on every quote.

Do you clean out the well before installing?

Yes. We remove leaves and debris, check that the drain at the bottom is open, and tell you if the drain is clogged or missing.

Can I still open the window for air?

Yes. Many covers can be lifted or propped open, and vented covers allow air to flow even when closed.

Do you replace old window wells?

Our focus is covers. If a well liner is rusted through, pulling away from the house, or too small for egress, we will tell you and explain the options.

When you’re ready

Request a quote

Share your city and well details — we’ll send a Free Estimate.

Request a quote

Or call (865) 381-0951

Knoxville Window Well Covers Call (865) 381-0951